HonestHomeCost
Septic

How much does septic tank installation cost?

Short answer

Fixr (updated January 31, 2025) puts septic tank installation at $4,500 to $9,000 with a national average of $6,100, a $3,000 low case and a $22,500 high case. This Old House (updated March 12, 2026) puts it at $3,480 to $11,625 and says complex systems can exceed $23,000, with its data sourced from Angi. Their tables by system type agree exactly on the three most expensive types, which matters because one table excludes installation and the other does not.

$6,100
National average for installing a septic tank system (Fixr)
$3,480 to $11,625
The typical range, from pricing estimates sourced from Angi (This Old House)
$4,500 to $9,000
The typical range for the same work (Fixr)
50% to 70%
The share of the total that labor accounts for (This Old House)

Two ranges for one job

Source Typical range Average Stated extremes Attributed to Updated
Fixr $4,500 to $9,000 $6,100 low end $3,000, high end $22,500 not stated January 31, 2025
This Old House $3,480 to $11,625 not stated complex systems can exceed $23,000 Angi March 12, 2026

Our arithmetic, marked as ours. The This Old House range is 1.81 times as wide as Fixr's. Its floor is $1,020 below Fixr's floor and its ceiling is $2,625 above Fixr's ceiling.

The extremes are the interesting part. Fixr's stated high end is $22,500. This Old House says complex systems can exceed $23,000. Those are $500 apart, or 1.02 times one another, while the two typical ranges they sit above are nothing like each other. The guides disagree about the ordinary job and very nearly agree about the worst one.

This Old House states where its figures come from: "The cost data featured in this guide was sourced using pricing estimates from Angi, unless otherwise noted."

Three of eight system types carry exactly the same price

Both guides price the job by system type. Eight types appear on both pages.

System type Fixr, materials only This Old House, average cost Same?
Aerobic $10,000 to $20,000 $10,000 to $20,000 identical
Mound $10,000 to $20,000 $10,000 to $20,000 identical
Evapotranspiration $10,000 to $15,000 $10,000 to $15,000 identical
Sand filter $6,000 to $10,000 $7,000 to $18,000 differs
Constructed wetland $6,000 to $10,000 $5,000 to $12,000 differs
Drip distribution $4,000 to $10,000 $8,000 to $18,000 differs
Chambered $3,500 to $10,000 $5,000 to $12,000 differs
Anaerobic $2,000 to $5,000 $3,000 to $8,000 differs

Three identical, five different. And the three that match are the three most expensive types in both tables.

Now read the column headings again. Fixr's column is "Cost (Materials Only)", and the page says above it that the costs "do not include installation". The This Old House column is "Average Cost", on a page about what installation costs.

So for an aerobic system, a mound system and an evapotranspiration system, the same two dollar figures are presented once as the price of the parts without installation and once as the average cost of the job.

Our arithmetic, marked as ours, using only This Old House's own numbers. That page states that labor typically accounts for 50% to 70% of the total cost. If that is right, materials are 30% to 50% of the total. On its own $10,000 figure for an aerobic system, the materials would be $3,000 to $5,000. Fixr prints $10,000 as the materials-only floor for the same system, which is 2 to 3.33 times that.

Our reading. Both tables cannot be labelled correctly. Either Fixr's figures include installation despite the heading, or This Old House's are parts prices presented as job prices. We cannot tell which from the two pages, and neither page gives a worked example that would settle it. What a reader can do with this is narrower but still useful: on the three expensive system types, treat the published figure as unresolved between parts and total, and ask any quote to state which it is.

Fixr's own table does not sit inside Fixr's own range

Fixr prints a second table, by the number of bedrooms, with the costs marked as installed.

Bedrooms Cost, installed Against Fixr's own $4,500 to $9,000 range
2 bedrooms $1,500 to $3,000 entirely below it
3 bedrooms $3,000 to $7,000 partly below it
4 bedrooms $7,000 to $12,000 partly above it
5 bedrooms $12,000 to $20,000 entirely above it

Our arithmetic, marked as ours. The 2 bedroom row tops out at $3,000, which is exactly Fixr's stated low end and $1,500 below the floor of its typical range. The 5 bedroom row starts at $12,000, which is $3,000 above the ceiling of its typical range.

So only part of one row, the 3 bedroom row, and part of the 4 bedroom row fall inside the headline range at all. Our reading: the headline describes a three to four bedroom house, and the page does not say so. If your house has two bedrooms or five, the number at the top of that page is not about you.

The contractor figures do not multiply out

Fixr gives three separate statements about the contractor on the same page:

  • Hiring a contractor for the project ranges between $1,500 and $4,000, covering system design, filing permits, excavating and installing.
  • The design alone usually costs between $600 and $800.
  • The hourly rate is between $150 and $200 per hour, and the page says it "should not change" with system type.
  • A typical installation job should take two to five days or 16 to 40 hours.

Our arithmetic, marked as ours. At those hourly rates and that job length, the labor alone comes to $2,400 at the cheapest and $8,000 at the dearest. The cheapest outcome is already $900 above the floor of the stated $1,500 to $4,000, and the dearest is twice its ceiling.

Our reading. The $1,500 to $4,000 figure cannot be the same thing as the hourly rate times the stated hours. One of the two is describing a narrower job. We flag it rather than pick, because the page gives no basis to pick.

The two guides disagree about permits

Fixr: a permit is an additional cost that depends on your municipality, and permits are "typically not more than $1,000".

This Old House: permit pricing varies from state to state, but permits usually cost $450 to $2,300.

Our arithmetic, marked as ours. The This Old House ceiling is $1,300 above the figure Fixr describes as an upper bound, which is 2.3 times it.

This Old House also prices a step Fixr does not put a number on in the same way: a percolation test at $700 to $2,000, quoting septic designer Rick Pezza that "to determine if you can even have a septic system, it starts with a perk test." Taken with the permit figure, that is a four figure sum spent before any digging, on a page whose floor is $3,480.

What the cheapest version looks like

This Old House puts the cheapest option at a plastic septic tank, $500 to $2,500, noting they are lighter, easier to install and resistant to water corrosion but more vulnerable to damage during installation.

Fixr prices tank materials separately, for a 1,000 gallon tank, materials only:

Material Materials only
Concrete $800 to $1,250
Plastic $830 to $1,400
Fiberglass $1,600 to $2,000

Our reading. The tank is not the project. On Fixr's own numbers the tank is a four figure item inside a five figure job, and on This Old House's numbers the labor is half to seventy percent of the bill. Choosing a cheaper tank material moves a small part of the total.

How to read an installation quote

Our view, marked as ours, drawn from the figures above.

  • Get the system type named in writing first. It is the largest single lever in both tables, from $2,000 to $20,000 at Fixr and $3,000 to $20,000 at This Old House.
  • Ask whether a quoted type price includes installation. On the three expensive types the two guides print the same dollars under opposite headings, so the published figure does not tell you.
  • Match the bedroom count to the row, not to the headline. Fixr's own table puts a two bedroom house below its headline range and a five bedroom house above it.
  • Budget the perc test and the permit before the install. $700 to $2,000 and $450 to $2,300 on This Old House's figures, spent whatever the answer turns out to be.
  • Treat anything near $22,500 as a site problem, not a tank choice. Both guides put their extreme there, and both tie it to system complexity and site conditions.
  • Plan the running cost at the same time. Our pumping page covers the interval and what the visit costs, and our inspection page covers the check that comes before any repair.

What to take from this

  1. The two typical ranges differ by a factor of 1.81 in width, while their extreme cases are only $500 apart.
  2. Three of eight system types carry identical prices, under a materials-only heading in one guide and an average-cost heading in the other.
  3. Those three are the three most expensive types, which is where the labelling matters most.
  4. Fixr's bedroom table falls largely outside Fixr's own headline range.
  5. Our arithmetic: Fixr's hourly rate times its own stated job length comes to $2,400 at the cheapest and $8,000 at the dearest, against a stated contractor total of $1,500 to $4,000.
  6. This Old House names Angi as the source of its cost data.

Sources

  1. Fixr, Septic System Installation Cost, updated January 31, 2025 (the $4,500 to $9,000 range, $6,100 national average, $3,000 low end and $22,500 high end, the cost table by number of bedrooms, the system type table labeled materials only, the tank material table, the contractor and design figures with the hourly rate and job length, the permit statement, and the replacement component figures)
  2. "This Old House, How Much Does a Septic Tank Installation Cost?, updated March 12, 2026 (the $3,480 to $11,625 range and the statement that complex systems can exceed $23,000, the system type table labeled average cost, the 50% to 70% labor share, the percolation test and permit figures, the cheapest tank figure, and the footnote attributing the cost data to Angi)"

Price figures are national US ranges from the sources above as of the date shown. Your local price depends on labor rates, permits and site conditions. Read how we get our numbers.