HonestHomeCost
Insulation

How much does blown-in insulation cost?

Short answer

Fixr's dedicated guide (updated August 29, 2025) puts blown-in insulation at $3,000 to $7,000 with an average of $5,000, and gives a rate of $1.65 to $3.80 per square foot. Its own general insulation page (updated January 29, 2026) says blown-in costs $0.50 to $2.30 per square foot. This Old House (updated July 10, 2025) puts blown-in cellulose at $0.60 to $2.30, sourced from contractor estimates used by Angi. The material rates reconcile them: fiberglass and wet spray cellulose are cheap, rockwool and dense pack cellulose are not.

$5,000
Average, walls and attic of a 2,000 sq ft home with a two-car garage (Fixr)
$1.65 to $3.80 per sq ft
Rate on the dedicated guide (Fixr)
$0.50 to $2.30 per sq ft
Rate for the same material on the same publisher's general page (Fixr)
$0.60 to $2.30 per sq ft
Blown-in cellulose, from contractor estimates used by Angi (This Old House)

One publisher, two rates, same material

Page Blown-in, per square foot Updated
Fixr, dedicated blown-in guide $1.65 to $3.80 August 29, 2025
Fixr, general insulation page $0.50 to $2.30 January 29, 2026
This Old House, blown-in cellulose $0.60 to $2.30 July 10, 2025

Our arithmetic, marked as ours. Fixr's two figures overlap only between $1.65 and $2.30. Its dedicated guide starts where its general page is already two thirds of the way up, and runs $1.50 higher at the top.

Our reading. Notice which of the three is the odd one out. The general Fixr page and the This Old House figure agree closely, $0.50 against $0.60 at the bottom and $2.30 at both tops, and they come by different routes, since This Old House names contractor estimates used by Angi. It is the dedicated guide, the page a search for this term is most likely to surface, that sits above both.

We cannot tell you which Fixr page is right. We can show you what reconciles them, because the same guide prints it.

The material rates reconcile the gap

Fixr's own breakdown, all four from the dedicated guide:

Material Cost per square foot
Blown fiberglass $0.50 to $1.10
Wet spray blown cellulose $0.60 to $1.80
Rockwool or mineral wool $1.40 to $2.10
Dense pack blown cellulose $2 to $2.30

Our reading, and it resolves the contradiction above without anyone being wrong. The two cheap materials, fiberglass at $0.50 to $1.10 and wet spray cellulose at $0.60 to $1.80, sit inside the $0.50 to $2.30 band that the general page and This Old House both give. The headline rate of $1.65 to $3.80 on the dedicated page does not match any single material row, so it is describing something else: a mix, or an installed job including access and labour, rather than the material in place.

So the question to ask a contractor is not what blown-in costs. It is which blown-in, because fiberglass and dense pack cellulose are a factor of four apart at the bottom and are both sold as blown-in insulation.

The totals, and what they assume

Figure Scope Source
$5,000 average Wall cavities and attic, cellulose, 2,000 sq ft home with a two-car garage Fixr
$3,000 to $7,000 The band around that Fixr
$900 low case Blown-in cellulose in garage walls only Fixr
$9,000 high case Mixed types in walls, ductwork, attic, garage and crawl space of a 3,000 sq ft home Fixr
$1.65 to $3.80 per sq ft New construction Fixr
$1.75 to $3.30 per sq ft Existing walls Fixr

Both ends are defined jobs rather than a price range, which is the habit we have been documenting across this site and the reason we now check every published band for it.

Note that existing walls are not dearer than new construction here, which is unusual: Fixr gives $1.75 to $3.30 for existing against $1.65 to $3.80 for new. The existing band is narrower at both ends rather than shifted upward. Fixr's own explanation is that only one type of blown-in works in existing wall cavities, which narrows the choice and with it the price.

The area table is the rate multiplied

Fixr publishes totals by area, from $165 to $380 at 100 square feet up to $4,950 to $11,400 at 3,000 square feet.

Our arithmetic, marked as ours. Every row is the $1.65 to $3.80 rate times the area: 100 by $1.65 is $165 and 100 by $3.80 is $380; 3,000 by $1.65 is $4,950 and 3,000 by $3.80 is $11,400. There is no quantity discount anywhere in the table, and no additional observation in it either.

That is worth knowing in both directions. It means you can skip the table and multiply your own area, and it means the table is not evidence that large jobs really cost that much.

Against the alternatives

Material Cost per square foot Source
Fiberglass batts $0.30 to $1.50 This Old House
Blown-in cellulose $0.60 to $2.30 This Old House
Spray foam $1 to $4.50 This Old House

Blown-in sits between batts and spray foam, which is also where it sits on convenience: it fills cavities that batts cannot reach without opening the wall, and it costs a fraction of foam.

This Old House adds the figure that most often decides a retrofit: removing existing insulation costs $1 to $2 per square foot, on top of installing the new. Our attic insulation page covers that and the federal tax credit, our spray foam page covers the dearest of the three, and our crawl space page covers the one place where the cheapest material is the wrong choice.

What to take from this

  1. Ask which blown-in. Fiberglass is $0.50 to $1.10 and dense pack cellulose is $2 to $2.30.
  2. The same publisher gives two rates for this material, $0.50 to $2.30 and $1.65 to $3.80, on two of its own pages.
  3. The cheaper figure agrees with This Old House, by a different route, which is the better reason to trust it.
  4. The area table is just the rate times the area, so multiply your own and skip it.
  5. Existing walls are not dearer than new here, because only one type fits them.

Sources

  1. Fixr, Cost to Install Blown-In Insulation, updated August 29, 2025 (the $3,000 to $7,000 range and $5,000 average with its stated scope, the $900 low case and $9,000 high case, the $1.65 to $3.80 rate, the new construction and existing wall rates, the area table, and the per-material rates for blown fiberglass, wet spray cellulose, rockwool and dense pack cellulose)
  2. Fixr, How Much Does Insulation Installation Cost?, updated January 29, 2026 (the $0.50 to $2.30 per square foot blown-in figure, cited here because it differs from the same publisher's dedicated guide)
  3. This Old House, Adding Insulation to Attic, updated July 10, 2025 (the $0.60 to $2.30 per square foot figure for blown-in cellulose, the comparison with fiberglass batts and spray foam, the removal cost, and the footnote attributing cost data to contractor estimates used by Angi)

Price figures are national US ranges from the sources above as of the date shown. Your local price depends on labor rates, permits and site conditions. Read how we get our numbers.