HonestHomeCost
Insulation

How much does spray foam insulation cost?

Short answer

This Old House (updated November 12, 2026) puts spray foam at $1 to $4.50 per square foot. Fixr (updated January 31, 2025) gives $3.15 to $7.50 per square foot for an existing home and $2.75 to $6.50 for new construction, with a whole-home average of $20,000. Bob Vila (updated June 11, 2024) gives $1,409 to $4,145 with an average of $2,756, from Angi and HomeAdvisor. The two are not independent: This Old House names Fixr among its sources, and its worked figures for a 1,500 square foot house are Fixr's four rates multiplied by 1,500, to the dollar. Use the per square foot rate and your own area.

$1 to $4.50 per sq ft
Headline rate, from HomeGuide, HomeAdvisor and Fixr (This Old House)
$3.15 to $7.50 per sq ft
Existing home, installed (Fixr)
$20,000
Whole-home average, 2,000 sq ft with 6 inches of foam (Fixr)
$0.44 to $8.70 per sq ft
The real spread, one inch open-cell to three inch closed-cell (This Old House)

The clearest case of borrowed numbers we have found

This Old House carries a footnote on the page: "The cost data featured in this guide is based on estimates from HomeGuide, HomeAdvisor, and Fixr, unless otherwise noted."

That is the publisher naming one of our own two sources. Usually that is as far as we can get. Here the page lets us go further, because it prints a worked example we can reproduce.

This Old House gives a typical 1,500 square foot house at $4,125 to $9,750 for a new home and $4,725 to $11,250 for an existing home.

Fixr gives its rates as $2.75 to $6.50 per square foot for new construction and $3.15 to $7.50 per square foot for an existing home.

Our arithmetic, marked as ours. All four figures reproduce exactly:

This Old House figure Fixr rate 1,500 sq ft
$4,125 $2.75 $4,125
$9,750 $6.50 $9,750
$4,725 $3.15 $4,725
$11,250 $7.50 $11,250

Four for four, to the dollar. This is not two publishers agreeing. It is one publisher's rate table multiplied by an assumed house size and printed by the other, and the second one says so in a footnote.

The same page contradicts its own headline

Here is why that matters rather than being a curiosity.

The headline rate on the This Old House page is $1 to $4.50 per square foot. Its own worked house example uses Fixr's rates, which run from $2.75 to $7.50.

Our arithmetic, marked as ours. A 1,500 square foot house at the page's own headline rate would be $1,500 to $6,750. The page instead prints $4,725 to $11,250 for that house. The two cannot both describe the same job.

The likeliest explanation is that the headline is a material rate and the worked example is an installed whole-home rate, but the page does not say so, and a reader comparing a quote has no way to tell which one applies to them.

What the rate actually depends on

Thickness, more than anything. This Old House prices it directly, and this table is the useful part of the page.

Thickness R-value Open-cell per sq ft Closed-cell per sq ft
1 inch 3.5 to 3.8 $0.44 to $1.50 $1.25 to $2.90
2 inches 7 to 7.6 $0.88 to $3.00 $2.50 to $5.80
3 inches 10.5 to 11.4 $1.30 to $4.50 $3.75 to $8.70

Our reading. From $0.44 to $8.70 is a factor of nearly twenty, and it is all inside one product. Any single number for spray foam without a thickness and a cell type attached is close to meaningless.

A second contradiction on the same page, and a third publisher settles it. The body text says closed-cell costs $1.25 to $1.50 per square foot while open-cell runs closer to $1.50 per square foot, which puts open-cell at or above closed-cell. Its own table above has open-cell cheaper than closed-cell at every one of the three thicknesses.

Bob Vila (updated June 11, 2024) prices the two by the board foot installed: open-cell $0.44 to $0.65 and closed-cell $1 to $1.50. So two of the three sets of figures, including This Old House's own table, put open-cell well below closed-cell, and only one sentence says otherwise. Closed-cell is the denser product with the higher R-value. The sentence is wrong and the tables are right.

Our arithmetic, marked as ours, and it is a small coincidence worth noting. Bob Vila's open-cell floor of $0.44 is the same figure This Old House gives for one-inch open-cell. Both publishers name overlapping upstreams: This Old House cites HomeGuide, HomeAdvisor and Fixr, and Bob Vila lists HomeAdvisor, Angi, HomeGuide and Fixr, three of the four names shared.

Totals, and what each one assumes

Figure Scope Source
$20,000 average Whole 2,000 sq ft existing home, 6 inches, mixed open and closed cell Fixr
$10,000 to $30,000 The band around that Fixr
$7,000 low case 7 inches of open cell on the attic floor only Fixr
$40,000 high case 10 inches of closed cell, net zero 3,000 sq ft home Fixr
$1,500 to $7,400, average $4,450 Attic This Old House
$1,500 to $5,600, average $3,550 Basement This Old House
$1,000 to $3,300, average $2,150 Around HVAC This Old House
$1,409 to $4,145, average $2,756 A home, attributed to Angi and HomeAdvisor Bob Vila
$1,500 to $3,500 Attic Bob Vila
$930 to $2,100 Garage Bob Vila

Our reading. Fixr's $20,000 is not a disagreement with This Old House's $4,450 attic figure; it is a whole house at six inches against one attic. This is the scope question we keep meeting, and here the publishers at least state their scope, which is more than most do.

Bob Vila's whole-home average of $2,756 sits below both, and the reason is visible in its own breakdown: it describes insulating parts of a house rather than filling one, and it treats spray foam as a material used sparingly because it is relatively costly. On the two attic figures the two publishers are close, $1,500 to $3,500 against $1,500 to $7,400, sharing a floor exactly.

One more arithmetic check worth knowing about

This Old House also prints an area table: 600 square feet at $600 to $2,700, average $1,650; 1,200 at $1,200 to $5,400, average $3,300; 2,000 at $2,000 to $10,000, average $6,000.

Our arithmetic, marked as ours. The first two rows are the headline rate multiplied: $600 is 600 by $1, $2,700 is 600 by $4.50, and $1,650 is 600 by $2.75, the midpoint. The same works for 1,200. The third row does not follow. At the headline rate, 2,000 square feet would be $2,000 to $9,000 with a midpoint of $5,500, not $10,000 and $6,000.

We cannot tell you why. We can tell you that two thirds of the table is arithmetic on the headline and the last third is something else, which is a reason to use the rate and your own measurements rather than reading a row off a table.

How to price your own job

Our view, marked as ours, drawn from the figures above.

  • Measure the area and decide the thickness first. Those two inputs move the price by more than any publisher's average.
  • Ask for open-cell or closed-cell in writing. They are different products at different prices, whatever the body text of any guide says.
  • Expect labour inside the rate, and expect the guides to disagree about how much of it. This Old House puts labour at $0.44 to $1.55 per foot; Bob Vila puts it at $1.50 to $4.90 per square foot. Our arithmetic: those two bands overlap only between $1.50 and $1.55.
  • In an existing home, ask about access. Bob Vila adds $293 to $875 where drywall has to come off to reach the stud spaces.
  • Compare like with like. A quote for the attic is not comparable to a whole-home figure, and most published averages are one or the other without saying which.
  • Check the tax credit. Our attic insulation page covers the federal credit, which applies to materials rather than labour.
  • Price the cheaper alternatives too. Our blown-in page covers the material that fills the same cavities for a fraction of the rate, and says which type is which.
  • If the space is a crawl space, our crawl space page separates insulating it from encapsulating it, which is a difference of more than double.

What to take from this

  1. The two guides are not independent. One names the other, and its worked figures are the other's rates times 1,500.
  2. $1 to $4.50 and $3.15 to $7.50 are both on offer, and the first page prints both without reconciling them.
  3. Thickness decides everything, from $0.44 to $8.70 per square foot.
  4. Open-cell is the cheaper product, confirmed by one publisher's own table at three thicknesses and by a second publisher's board foot rates.
  5. Ask what area a total covers. $20,000 is a whole house; $4,450 is an attic.

Sources

  1. This Old House, How Much Does Spray Foam Insulation Cost?, updated November 12, 2026 (the $1 to $4.50 headline rate, the thickness and area tables, the location figures, the labour rate, the worked 1,500 square foot house figures, and the footnote attributing the data to HomeGuide, HomeAdvisor and Fixr)
  2. Fixr, Cost to Install Spray Foam Insulation, updated January 31, 2025 (the $10,000 to $30,000 range and $20,000 average with its stated scope, the $7,000 low case and $40,000 high case, and the per square foot rates for new construction and existing homes)
  3. Bob Vila, Spray Foam Insulation Cost, updated June 11, 2024 (the $1,409 to $4,145 range and $2,756 average attributed to Angi and HomeAdvisor, the open-cell and closed-cell board foot rates, the labour rate, the area figures, the attic and garage figures, the drywall access cost, and the article source list naming HomeAdvisor, Angi, HomeGuide and Fixr)

Price figures are national US ranges from the sources above as of the date shown. Your local price depends on labor rates, permits and site conditions. Read how we get our numbers.